← Construction & Home Improvement Calculators

The Complete Guide to Construction Costs: Concrete, Roofing, Flooring, and More

Construction costs start with measurements, not prices: square footage sets the area, the roof pitch stretches it, and depth turns area into volume. A 2,000-square-foot roof at a 6/12 pitch needs about 25 roofing squares, and a 10-by-10-foot patio 4 inches deep needs 1.23 cubic yards of gravel. This guide shows how to work out each number before ordering materials.

By Jacob Levy, Founder of FigureQuick.com · Last reviewed 2026-11-19

Square footage: the number everything starts from

Almost every construction cost starts with square footage. Flooring is sold by the square foot, paint coverage is quoted in square feet, roofing starts from the footprint in square feet, and heating and cooling loads are estimated per square foot of floor area. Getting this one number right is what makes every estimate that follows either accurate or wrong by the same percentage.

Square footage is the area of a space, found by multiplying its length by its width. Measure both sides in feet and the result is in square feet. A room 20 feet long and 15 feet wide covers 300 square feet. The same area is also shown in square yards, which is the square footage divided by 9, so 300 square feet is 33.33 square yards, and in acres, which is the square footage divided by 43,560 — useful when the space is large enough that square feet become an unwieldy number.

For a simple rectangle, one length and one width measurement is all it takes. For an L-shaped room or an irregular plot, split the space into rectangles, work out the square footage of each piece separately, and add the results together. That keeps the math exact instead of guessing an average length or width. Measure the longest points, and round up slightly when buying materials: flooring, paint, and turf all come in fixed sizes and leave offcuts, so adding about 10 percent to the measured area covers waste and mistakes without overspending. The Square Footage Calculator works out the area for any length and width, including the square-yard and acre conversions.

Flooring and tile: net area, waste, and whole boxes

Ordering flooring starts with the net room area — length times width — then adds a waste allowance for cuts, pattern matching, and damaged pieces. The formula is Boxes Required = CEILING([Length × Width × (1 + Waste %)] ÷ Sq Ft Per Box). The result is always rounded up to whole cartons, because flooring is sold by the box and a partial box cannot be ordered.

Material cost is simply the number of boxes times the price per box, and the covered area of those boxes is always a little more than the gross area needed — that leftover is repair stock. Installation labor is charged on the net room area, not the gross area, since the installer is not laying the waste pieces. The total installed cost is material plus labor. Use a 10% waste factor for a straight lay and 15% for herringbone or diagonal tile, where every angled cut leaves a scrap. Check the actual coverage printed on the box rather than assuming it — coverage varies by plank and tile size — and keep at least one spare box from the same dye lot for future repairs, because a later batch can be a slightly different shade.

Worked example: flooring an 18 ft by 22 ft room. The net area is 18 × 22 = 396 square feet. With a 10% waste allowance the gross area is 396 × 1.10 = 435.6 square feet. At 23.6 square feet per box, that needs 435.6 ÷ 23.6 = 18.46 boxes, rounded up to 19 boxes, which cover 19 × 23.6 = 448.4 square feet. At $68 a box the material cost is 19 × $68 = $1,292. Installation labor at $3.25 per square foot is charged on the net 396 square feet, which is $1,287, so the total installed cost is $1,292 + $1,287 = $2,579. The Flooring & Tile Calculator reproduces this example exactly — enter the same room, waste, coverage, box price, and labor rate and it returns the same 19 boxes and $2,579 total.

Roofing: the footprint is not the roof

A roof is bigger than the footprint of the house it covers, because the slope stretches the surface. The formula is Roofing Squares = [(Footprint Sq Ft × Roof Pitch Multiplier) × (1 + Waste %)] ÷ 100. One roofing square is 100 square feet of roof surface. The pitch multiplier turns a flat footprint into sloped area — a 4/12 pitch is 1.054x, a common 6/12 pitch is 1.118x, an 8/12 pitch is 1.202x, and a steep 12/12 mansard is 1.414x. A steep roof can have 20% to 40% more surface than the footprint it covers, which is the most common reason a roofing estimate comes in low.

Shingles are sold by the bundle, with 3 bundles per square, and the bundle count is always rounded up — a half bundle cannot be ordered and the extra covers starter strips and ridge caps. Shingle material cost is bundles times the price per bundle. Tear-off, underlayment, flashing, and labor are charged per square, so the turnkey estimate is material plus labor per square times the number of squares. Use about 10% waste for a simple gable roof and 15% for a roof with hips, valleys, and dormers, where every cut leaves a scrap. Include the roof overhangs in the footprint — roughly 100 to 150 extra square feet — and get the pitch right before ordering anything.

Worked example: a 2,000 sq ft footprint with a 6/12 pitch. The sloped area is 2,000 × 1.118 = 2,236 square feet. With 12% waste that becomes 2,236 × 1.12 = 2,504.32 square feet, or 25.0 roofing squares. Shingle bundles are 25.0 × 3 = 75.13, rounded up to 76 bundles. At the calculator's example rates of $42 a bundle and $260 a square for labor, the material cost is 76 × $42 = $3,192, the labor is 25.0 × $260 = $6,511.23, and the total turnkey estimate is $9,703.23. The bundle and labor rates are example defaults, not quotes — enter local rates to get a local estimate. The Roofing Calculator reproduces this example exactly with the same footprint, pitch, waste, bundle cost, and labor rate.

Gravel and mulch: area times depth is volume

Gravel and mulch are sold by volume, not by weight or by area, and the volume comes from the same three measurements: length, width, and depth. Multiply the length by the width to get the area, then multiply by the depth — converted from inches to feet by dividing by 12 — to get cubic feet. Divide by 27 to convert cubic feet to cubic yards, since a cubic yard is 3 feet by 3 feet by 3 feet.

To estimate the weight of gravel, the calculator uses the standard estimate that one cubic yard of gravel weighs about 1.4 tons. The exact weight varies with the type of stone and how wet it is, so treat the tons figure as a planning estimate for ordering and delivery, not an exact scale weight. Mulch is usually sold in bulk by the cubic yard or in bags that hold 2 cubic feet each: divide the cubic feet by 2 and round up for the number of bags, because a partial bag cannot be bought and it is better to have a little left over than to run short halfway through a bed.

Worked example: gravel for a 10 ft by 10 ft patio, 4 inches deep. The area is 100 square feet and the depth is 4 ÷ 12 = 0.333 feet, so the volume is 100 × 0.333 = 33.33 cubic feet. That is 33.33 ÷ 27 = 1.23 cubic yards, weighing about 1.23 × 1.4 = 1.73 tons. The Gravel Calculator reproduces this example exactly.

Worked example: mulch for a 20 ft by 10 ft bed, 3 inches deep. The area is 200 square feet and the depth is 3 ÷ 12 = 0.25 feet, so the volume is 200 × 0.25 = 50.00 cubic feet. That is 50 ÷ 27 = 1.85 cubic yards, or 50 ÷ 2 = 25 bags of 2 cubic feet each. For most garden beds, a depth of 2 to 3 inches is enough to hold in moisture and keep weeds down. Piling mulch deeper than 4 inches, or heaping it against the trunk of a tree or shrub, can trap too much moisture and cause rot, so keep it a few inches away from stems and trunks. The Mulch Calculator reproduces this example exactly.

Stairs: risers, treads, and total run

A staircase is planned from its total rise, the vertical distance from one finished floor to the next, and its tread depth, the horizontal depth of each step. The number of risers is found by dividing the total rise by the standard riser height of 7.5 inches and rounding up, so every step is the same height and none is taller than the standard. The actual riser height is then the total rise divided by that number of risers.

There is always one fewer tread than there are risers, because the top step lands on the upper floor itself. The total run, the horizontal length the staircase takes up, is the number of treads multiplied by the tread depth. Keep every riser the same height: even a small difference between steps is a tripping hazard, because people expect each step to feel the same. If the total rise does not divide evenly, the calculator spreads the difference across all the risers rather than leaving one odd step at the top or bottom.

Use this calculator with clients → White-label.

Worked example: a staircase with a 60-inch total rise and 10-inch treads. The riser count is 60 ÷ 7.5 = 8 risers, each 60 ÷ 8 = 7.50 inches high. There are 8 − 1 = 7 treads, and the total run is 7 × 10 = 70.00 inches. The Stair Calculator reproduces this example exactly — enter the same total rise and tread depth and it returns the same 8 risers, 7 treads, and 70-inch run.

Heating, cooling, and electricity

Two more numbers belong in a construction budget: how much heating or cooling a room needs, and how much electricity its appliances use. A BTU, or British Thermal Unit, is a measure of heating or cooling power, and the quickest way to size a room is the rule of thumb of 20 BTUs per square foot of floor area. Multiply the room's length by its width to get the floor area, then multiply by 20. The calculator also adjusts for ceiling height: the rule assumes a standard 8-foot ceiling, so a taller room needs proportionally more capacity, which is why the result is scaled by the ceiling height divided by 8. When shopping, compare the BTU rating on the unit with the estimate and round up to the nearest available size rather than down — a slightly oversized heater or air conditioner handles the hottest and coldest days more comfortably than one that is always running at its limit.

Worked example: heating and cooling a 12 ft by 10 ft room with an 8 ft ceiling. The floor area is 12 × 10 = 120 square feet, and 120 × 20 = 2,400 BTU of heating or cooling. The BTU Calculator reproduces this example exactly.

Electricity use is measured in kilowatt-hours: one kilowatt-hour is 1,000 watts used for one hour. To find an appliance's daily use, multiply its wattage by the hours it runs each day and divide by 1,000. Multiply that daily figure by 30 for a month, then multiply by the price per kilowatt-hour to get the cost. The current the appliance draws is its watts divided by the voltage of the circuit it is plugged into. Use the amps figure to check a circuit before plugging in a heavy appliance: a standard household circuit is usually rated for 15 or 20 amps, and the total current of everything on that circuit should stay comfortably below that rating. The daily and monthly costs are estimates based on the hours entered, so they are only as accurate as that guess — a device that runs in bursts, like a refrigerator or a heater with a thermostat, does not draw its full wattage all the time, so its real cost will be lower than a figure based on its rated watts running nonstop.

Worked example: a 100-watt bulb running 5 hours a day. Daily use is 100 × 5 ÷ 1,000 = 0.50 kWh, monthly use is 0.50 × 30 = 15.00 kWh, and the cost is 15.00 × $0.15 = $2.25 a month at $0.15 per kWh. The Electricity Calculator reproduces this example exactly.

Common mistakes

The most expensive mistakes in construction estimating are usually arithmetic, not judgement. The first is using the flat footprint as the roof area and forgetting the pitch — a 6/12 roof has about 12% more surface than its footprint, and a steep roof far more. The second is ordering the exact measured area of flooring with no waste allowance, and running short with one row to go. The third is charging installation labor on the gross area instead of the net area, which overstates the labor bill. The fourth is ordering gravel or mulch by weight or by area instead of by volume, and the fifth is measuring a room at its narrowest points instead of its longest, which understates the area and everything ordered from it.

A sixth mistake is treating a calculator's example rates as quotes. The bundle cost, labor rate, and electricity price in the worked examples are the calculators' example defaults, chosen so the arithmetic can be checked — real rates vary by supplier, region, and season, so enter local figures before ordering or budgeting. And a seventh is ordering materials before the measurements are final: a room re-measured after the walls move, a roof re-pitched after the plans change, or a bed re-dug deeper than planned all change the numbers, and the order should follow the final measurements, not the first ones. Each of these is a calculation, and each has a calculator in the table below.

Every tool in this cluster

The table below lists every calculator in this cluster on FigureQuick, with the situation each one is for.

CalculatorUse this when
BTU CalculatorEstimating the heating or cooling a room needs in BTUs from its length, width, and ceiling height.
Electricity CalculatorWorking out how much electricity an appliance uses in kilowatt-hours, what it costs, and the current it draws.
Flooring & Tile CalculatorWorking out how many boxes of flooring or tile a room needs, with waste, material cost, and installation labor.
Gravel CalculatorWorking out how much gravel a driveway, path, or patio needs, in cubic feet, cubic yards, and tons.
Mulch CalculatorWorking out how much mulch a garden bed needs, in cubic feet, cubic yards, and standard 2-cubic-foot bags.
Roofing CalculatorTurning a house footprint into roofing squares, shingle bundles, and a full replacement cost — pitch and waste included.
Square Footage CalculatorWorking out the square footage of a room or plot from its length and width, with square-yard and acre conversions.
Stair CalculatorPlanning a staircase: riser count, riser height, tread count, and total run from the total rise and tread depth.

Sources and methodology

Every figure in this guide comes from the standard formula stated on the calculator it describes, and every worked example was re-computed in Python against that calculator's own specification. Square footage, flooring boxes, roofing squares, gravel and mulch volume, stair risers, BTU load, and electricity use are all arithmetic from the measurements entered — length, width, depth, pitch, and rate — with no external tables. The pitch multipliers (4/12 at 1.054x, 6/12 at 1.118x, 8/12 at 1.202x, 12/12 at 1.414x), the 7.5-inch standard riser height, the 20 BTU per square foot rule of thumb, and the 1.4 tons per cubic yard gravel weight are the standard estimates each calculator states in its own explanation. The bundle cost of $42 and labor rate of $260 per square in the roofing example, the $68 box price and $3.25 per square foot labor in the flooring example, and the $0.15 per kWh electricity price are the calculators' example defaults, labelled as such — enter local rates for a local estimate. This guide is educational: it describes what the calculators compute, not advice about which materials or contractors to choose. Last reviewed 2026-11-19.

Frequently asked questions

How do I find a room's square footage?

Measure the length and width of the room in feet and multiply them together. A room 20 feet long and 15 feet wide covers 300 square feet. For an L-shaped room, split it into rectangles, work out each piece separately, and add the results. The Square Footage Calculator does the multiplication and also converts the result to square yards and acres.

How do I measure square feet?

Measure the longest points of each side with a tape measure, in feet, then multiply length by width. To convert, divide square feet by 9 for square yards and by 43,560 for acres. When buying materials, add about 10 percent to the measured area to cover cuts, waste, and mistakes.

How much gravel do I need for a 10 by 10 patio?

At 4 inches deep, a 10 ft by 10 ft patio needs 33.33 cubic feet of gravel, which is 1.23 cubic yards weighing about 1.73 tons. The volume is length times width times depth in feet (4 inches is 0.333 feet), divided by 27 for cubic yards. The Gravel Calculator works this out for any size and depth.

How many roofing squares do I need?

Multiply the footprint in square feet by the roof pitch multiplier, add the waste percentage, and divide by 100. A 2,000 sq ft footprint with a 6/12 pitch (1.118x) and 12% waste needs 25.0 roofing squares, or 76 shingle bundles at 3 bundles per square. The Roofing Calculator works this out for any footprint, pitch, and waste factor.

How much mulch do I need for a garden bed?

Multiply the bed's length by its width and by the depth in feet, then divide by 27 for cubic yards or by 2 for standard 2-cubic-foot bags. A 20 ft by 10 ft bed mulched 3 inches deep needs 50.00 cubic feet, or 1.85 cubic yards — 25 bags. A depth of 2 to 3 inches is enough for most beds.

How do you calculate stairs?

Divide the total rise by the standard riser height of 7.5 inches and round up to get the number of risers, then divide the total rise by that count for the actual riser height. There is one fewer tread than risers, and the total run is treads times tread depth. A 60-inch rise with 10-inch treads gives 8 risers of 7.50 inches, 7 treads, and a 70-inch run.

How many BTUs do I need for a room?

Use the rule of thumb of 20 BTUs per square foot of floor area, adjusted for ceiling height by dividing the height by 8. A room 12 feet long and 10 feet wide with an 8-foot ceiling has 120 square feet and needs about 2,400 BTU of heating or cooling. Round up to the nearest available unit size when shopping.

More Construction & Home Improvement Calculators

← Back to all calculators